All Products

1. Acryflex Fine

A cement-based, high-density, patching, topping and underlayment material applied by trowel from a feather-edge up to 1/4”. Designed to be mixed with Add Mix-21.

1. Add Mix-21

An acrylic, liquid additive (21% solids) for cement based mixes designed to increase adhesive bond as well as tensile and flexural strength.

1. CrownShield MVB (Moisture Barrier)

CrownShield MVB is a clear 2-component, 100% solids, low odor, low viscosity epoxy that is specifically formulated as a moisture barrier coating to treat new and existing concrete floors with high moisture and high pH.

data sheet |   msds sheet  

1. Geocel Pro Flex Tripolymer Sealant Caulk

A single component, high performance elastomeric caulk which adheres to masonry, wood, asphalt, metal and vinyl for use in a wide variety of roofing and general construction applications. May be applied to damp or oily surfaces in a wide range of temperatures.

1. Transeal

An exterior-grade, clear, solvent-based acrylic sealer applied over properly prepared masonry and concrete surfaces. Transeal forms a durable, flexible film which provides long lasting protection. Transeal is available in Clear (Gloss or Matte).

An exterior-grade, clear, solvent-based acrylic sealer applied over properly prepared masonry and concrete surfaces. Transeal forms a durable, flexible film which provides long lasting protection. Transeal is available in Clear (Gloss or Matte).

1. Transeal

Transeal is a clear, solvent based, high gloss, acrylic sealer designed to be applied over properly prepared concrete pavers, brick, block, concrete, stucco, natural stone, flagstone, granite, limestone and bluestone. Forms a durable, flexible film providing long lasting protection. Exterior applications only.

1. U-Coat 260 (Membrane)

U-Coat 260 is a two component, fast setting, fast curing, solvent free, flexible, high performance and high solids polyurethane elastomeric membrane applied to interior or exterior concrete, plywood and metal surfaces. May be applied at any rate to achieve desired thickness. Gray in color.

1. U-Coat 555 Pedestrian/Vehicular Deck Systems

A fast setting, rapid curing, 100% solids, polyurethane/polyurea, liquid applied, chemically cured, waterproof coating system. U-Coat 555 Pedestrian and Vehicular Traffic Deck Systems are user friendly, low odor systems specifically designed to be tough and durable enough to withstand light to heavy traffic.

data sheet |   msds sheet  

1. U-Plug

U-Plug is a fast-setting (3-5 minutes), hydraulic cement designed to instantly stop running water from seeping through holes and cracks in masonry and concrete. U-Plug exhibits excellent adhesion
& exceptional structural strength while providing a long lasting, permanent repair.

1. U-Trowel

A cement-based, waterproof, traditional stucco applied by trowel over properly prepared masonry and concrete surfaces. One coat produces a high density finish which may be applied in a wide variety of textures. Designed to be mixed with Add Mix-35.

1. Universal 1023

Universal 1023 is a cement-based, durable, multi-purpose, polymer-modified, high-strength and water resistant patching, repair and resurfacing material which may be applied from a feather-edge up to 6" thick for horizontal applications and up to 2" thick for vertical applications.

1. Xtreme-Bond Stone Mortar

A high-performance, polymer-modified mortar designed to provide optimum bond, exceptional sag resistance and durability when installing thin-stone veneers, thin-brick veneers or tile over properly prepared substrates. Xtreme-Bond Stone Mortar meets the requirements of a Type S mortar.

2. Acryflex Regular

A cement-based, high-density, patching, topping and underlayment material applied by trowel from 1/8” up to 3/4”. Designed to be mixed with Add Mix-21.

2. Add Mix-35

An acrylic, liquid additive (35% solids) for cement based mixes designed to increase adhesive bond as well as tensile and flexural strength.

2. CrownShield WB (Primer)

CrownShield WB is a low VOC, 2-component, water-based, polyamide epoxy floor coating recommended to be applied as a concrete sealer prior to topcoat application in order to help prevent outgassing.

data sheet |   msds sheet  

2. Geocel Pro Flex Tripolymer Brushable Sealant

A clear, brushable, rubber like sealant for use in a wide variety of general construction and roofing applications. Ultra-Seal adheres to masonry, concrete, wood, asphalt and metal surfaces. May be applied to damp or oily surfaces in a wide range of temperatures.

2. Thin-Stone Veneer Mortar

A durable, polymer-modified mortar designed to provide optimum bond when installing natural, thin-stone veneer over properly prepared substrates.

2. Transeal WB

An interior/exterior, durable, waterborne acrylic sealer applied over properly prepared masonry and concrete surfaces. Transeal WB is low odor making it an ideal sealer to use for interior applications. Transeal WB is available in Clear (Gloss).

2. Transeal WB

Transeal WB is a clear, low odor, water based acrylic sealer designed to be applied over properly prepared concrete, pavers, brick, block, concrete, stucco, natural stone, flagstone, granite, limestone and bluestone. Transeal WB forms a durable, flexible film providing long lasting protection. Provides excellent adhesion and hot tire resistance.

2. Transeal WB (Clear)

A clear, interior/exterior, durable, waterborne acrylic sealer applied over properly prepared masonry and concrete surfaces. Transeal WB is low odor making it an ideal sealer to use for interior as well as exterior applications. Transeal WB is available in Clear (Gloss).

2. U-Coat 295 (Topcoat)

U-Coat 295 is a two component, fast setting, rapid curing, solvent free, 100% solids, hybrid, aliphatic, polyurea elastomeric membrane applied to interior or exterior concrete, plywood and metal surfaces. Suitable for single or multiple applications in temperatures as low as 20°F. Available in Dolphin Gray and Tan.

data sheet |   msds sheet  

2. U-Coat 3000 Waterproofing Membrane System

The U-Coat 3000 waterproofing membrane system is a user-friendly, liquid applied, waterproofing membrane. The system uses one or two coats of a fast setting, water catalyzed polyurethane coating and protection board. It is an elastomeric system designed to expand and contract with normal structural movements.

data sheet |   msds sheet  

2. U-Seal

A cement-based, waterproof coating applied by brush or spray over properly prepared, vertical masonry and concrete surfaces. U-Seal creates a permanent waterproof barrier which prevents moisture migration. An ideal coating to use for waterproofing interior/exterior foundation walls. Designed to be mixed with Add Mix-35.

2. U-Trowel Basecoat

A cement-based, fiber-reinforced basecoat for U-Trowel, stucco finishes, manufactured stone and thin stone veneers. U-Trowel Basecoat may be applied by trowel over a variety of surfaces (including metal lath). Designed to be mixed with Add Mix-35.

2. VHO Patch

A fast-setting (15-20 minutes), cement-based, polymer-modified material designed to repair vertical, horizontal and overhead concrete and masonry surfaces up to 2” thick in one application.

3. Bond All Exterior

A brushable, water-based, exterior-grade, surface bonding agent designed to be applied to the substrate prior to applying cement based and gypsum mixes.

3. Color-Seal

Color-Seal is a water-based, low odor, acrylic stain and sealer designed to be applied over concrete, brick block, stucco and concrete pavers. Color-Seal provides long lasting protection while improving the appearance of the substrate by add adding color. Provides excellent adhesion and hot tire resistance.

3. CrownShield 50 (Basecoat)

CrownShield 50 is a two-component, 100% solid epoxy base-coat for general use. Available in Clear or pigmented.

data sheet |   msds sheet  

3. Geocel 3500 Polyurethane Bonding Sealant

A premium adhesive which may be used for a variety of bonding applications such as adhering caps to landscape block walls, thin-brick panel systems and the installation of roof tile. Easy to apply with a standard caulk gun.

3. Manufactured Stone Mortar

A durable, polymer-modified mortar designed to provide optimum bond when installing a variety of manufactured stone veneers over properly prepared substrates.

3. Non-Shrink Grout

A non-shrink, high strength, non-metallic cementitious grouting compound which may be poured or troweled when used for a variety of anchoring and patching applications.

3. Self-Leveler 4000

A cement-based, polymer-modified, self-leveling, resurfacing compound that can be poured or pumped over a variety of uneven, properly prepared surfaces from a featheredge up to two inches in a single pour.

3. Siloxane 12

An exterior-grade, clear, deep-penetrating, solvent-based water repellent applied over untreated masonry and concrete surfaces.

3. Siloxane WB

An interior/exterior-grade, clear, waterborne, deep-penetrating water repellent applied over untreated masonry and concrete surfaces

3. Surface Bonding Cement

A cement-based, fiber-reinforced, polymer- modified, waterproof coating designed to be applied by trowel over dry stacked concrete block, rigid insulation board, masonry and concrete surfaces.

3. U-Coat 5000 Waterproofing Membrane System

The U-Coat 5000 waterproofing membrane system is a user-friendly, high solids, single component, liquid applied, waterproofing membrane for cured or green concrete. U-Coat 5000 is available as 5000V for Vertical surfaces and 5000H for Horizontal surfaces. The system uses two coats of a modified polyurethane coating and protection board. It is an elastomeric system designed to expand and contract with normal structural movements.

data sheet |   msds sheet  

3. U-Coat 5000V

U-Coat 5000V is a single component, liquid applied, bitumen modified, coal tar free, moisture cured, polyurethane waterproofing membrane for vertical surfaces. Black in color.

3. U-Coat 527 (Topcoat)

U-Coat 527 is a high solids, two-component, liquid applied, aliphatic polyaspartic polyurea which exhibits excellent retention, gloss and UV stability. U-Coat 527 is quick curing and specifically formulated to be installed in thin film applications (8-12 mils in a single pass). An excellent topcoat over aromatic polyurea, polyurethane and epoxy applications. Available in Clear, Dolphin Gray and Tan.

data sheet |   msds sheet  

4. Bond All Interior

A brushable, water-based, interior-grade, surface bonding agent designed to be applied to the substrate prior to applying cement based and gypsum mixes.

4. Concrete Cure & Seal

Concrete Cure & Seal is a waterborne acrylic emulsion designed to cure, seal, harden and dustproof new or older concrete substrates. Forms a membrane on new concrete which retains water, allowing normal hydration. Contains no fillers, extenders, waxes or flammable solvents

4. CrownClear (Clear Topcoat)

CrownClear is a clear, 2-component, 100% solids, UV resistant, epoxy topcoat.

data sheet |   msds sheet  

4. Flash-Patch

A fast-setting (20 minutes), cement-based, polymer-modified, patching and leveling material applied by trowel over concrete, masonry and plywood surfaces for applications up to 1/2”.

4. Geocel 3900 Textured Polyurethane Sealant

A single component, high performance sealant that is durable and ideal for non-structural mortar repairs and blending dissimilar surfaces. It bonds to both porous and non-porous substrates while providing the appearance of mortar.

4. Siloxane 12

An exterior-grade, clear, deep-penetrating, solvent-based water repellent applied over untreated masonry and concrete surfaces.

4. Siloxane 20

An exterior-grade, clear, deep-penetrating, solvent-based water repellent applied over untreated masonry and concrete surfaces.

4. Thinset Mortar

A cement-based, bond coat used to set all types of tile over properly prepared horizontal concrete and masonry surfaces.

4. U-Coat 129

U-Coat 129 is a two component, liquid applied, asphalt extended aromatic polyurethane that adheres to most substrates, to form a waterproof membrane. U-Coat 129 is an ideal coating for tank liners and containment storage. Safe for use when in contact with potable water.

data sheet |   msds sheet  

4. U-Coat 5000H (Membrane)

U-Coat 5000H is a single component, liquid applied, bitumen modified, coal tar free, moisture cured, polyurethane waterproofing membrane for horizontal surfaces. * All exposed membrane surfaces must be protected by installing protection board. Black in color.

4. U-Coat Color Chart

U-Coat Color Chart. Please note that color samples may differ from actual product. Variations in color due to job conditions and method of application should also be expected. Always do a sample panel on site to ensure color and texture approval by owner or architect. For exact color ask for draw down film sample. Not all colors are available in all products. Refer to product data sheet for info.

data sheet |   msds sheet  

4. U-Plug

A fast-setting (5-10 minutes), non-shrink, hydraulic cement designed to instantly stop running water from seeping through holes and cracks found in masonry and concrete.

4. U-Seal

U-Seal is a cement based, waterproof coating designed to be applied by brush or spray over masonry and concrete surfaces. U-Seal creates a permanent waterproof barrier which prevents moisture migration and seals out water & dampness against hydrostatic pressure.

5. Cold Check

A chloride-based, liquid admixture designed to accelerate the set time of concrete and mortar mixes in cold weather applications.

5. CrownShield (Pigmented Topcoat)

CrownShield is a pigmented, 2-component, 100% solids epoxy topcoat for indoor use where UV resistance is required.

data sheet |   msds sheet  

5. Feather-Edge

A fast-setting (20 minutes), cement-based, polymer-modified compound used to smooth interior surfaces (from 1/4” down to a true feather-edge) prior to the installation of a variety of floor coverings such as ceramic tile, VCT, sheet vinyl and carpeting.

5. Geocel 3300 Polyurethane Sealant

A single component, high performance polyurethane sealant that withstands adverse weather conditions and cures to a flexible weatherproof seal

5. Glass Block Mortar

A high strength, polymer-modified, waterproof mortar designed for setting a variety of decorative glass block.

5. Siloxane 20

An exterior-grade, clear, deep-penetrating, solvent-based water repellent applied over untreated masonry and concrete surfaces.

5. Siloxane WB

Siloxane WB is a clear, water based, deep penetrating water repellent designed to be applied over untreated concrete pavers, brick, block, concrete, stucco and natural stone. Breathable, protects without forming a film or leaving a sheen. May be used for vertical and horizontal applications.

An interior/exterior-grade, clear, waterborne, deep-penetrating water repellent applied over untreated masonry and concrete surfaces

5. Styrocoat

A cement-based, polymer-modified basecoat for synthetic stucco finishes (Umaco Finish-Coat). Applied by trowel, Styrocoat embeds fiberglass reinforced mesh fabric over expanded polystyrene insulation board (EPS) and cement board. Styrocoat may also be used to adhere EPS to vertical concrete, masonry and exterior grade plywood surfaces.

5. Tite-Roc

A fast-setting, pourable, expanding, hydraulic material designed for anchoring fixtures in concrete and masonry.

5. U-Coat 3000 (Membrane)

U-Coat 3000 is a seamless and joint free waterproofing system created from a single component, water curable liquid applied, coal tar free, urethane/polyurea roofing and waterproofing membrane system for vertical and horizontal surfaces. The coating may be applied in the field from 30 to 2500 mils (0.076 -6.35 cm) in one application while supplying simultaneous curing throughout the coating. Black in color.

data sheet |   msds sheet  

5. U-Coat General Guidelines

These guidelines cover Safety and Storage, Job Conditions, Priming, Expansion Joints, and Coating Applications. Please refer to these guidlines before applying any Umaco U-Coat product.

data sheet |   msds sheet  

6. Block-Filler

Designed to prime porous surfaces of cement, concrete & lightweight masonry blocks. Suitable for use beneath both interior and exterior coatings. May be top coated with oil, alkyd or latex coatings.

6. Color-Seal

Color-Seal is a water based, low odor, acrylic stain and sealer designed to be applied over concrete, brick, block, stucco & concrete pavers. Color-Seal provides long
lasting protection while improving the appearance of the substrate by adding color.

6. CrownPro 8072 (Polyaspartic)

CrownPro 8072 is an aliphatic, environmentally friendly, UV resistant, polyaspartic surface topcoat for flooring systems which has a long working time and pot life.

data sheet |   msds sheet  

6. Geocel 1500SL Self-Leveling Concrete Joint & Crack Sealant

A high performance, one-part, moisture curing, self-leveling sealant for concrete or asphalt joints. Its non-gassing properties make it ideal for high temperature and humid conditions.

6. NCA (Non-Chloride Accelerator)

A non-chloride additive (in dry powdered form) designed to accelerate the set time of concrete and mortar mixes while increasing early compressive strength. NCA does not promote steel corrosion or efflorescence.

6. Perma-Finish

A 100% acrylic-based, aggregate-textured, synthetic stucco applied over properly prepared expanded polystyrene insulation board, cement board, concrete, masonry, exterior-grade plywood, plaster and stucco surfaces. Perma-Finish is ready to use and is available in a variety of colors and textures.

6. Siloxane 12

Siloxane 12 is an exterior grade, solvent based, clear, deep penetrating water repellent designed to be applied over untreated concrete pavers, brick, block, concrete, stucco, and natural stone. Breathable, does not form a film or leave a sheen. May be used for vertical or horizontal applications.

6. U-Coat Primer

U-Coat Primer is a two-component, high solids, liquid applied, epoxy-polyamine primer with exhibits unique penetrating characteristics. U-Coat Primer is designed to be applied over properly prepared concrete and plywood surfaces prior to the installation of U-Coat polyurethane coatings.

data sheet |   msds sheet  

6. Universal 1023

Universal 1023 is a cement-based, durable, multi-purpose, polymer-modified, high-strength and water resistant patching, repair and resurfacing material which may be applied from a feather-edge up to 6" thick for horizontal applications and up to 2" thick for vertical applications. Available in Gray or White.

7. Act Fibers

Alkaline resistant fibers which help reinforce against plastic shrinkage crack formation when added to cement-based and gypsum-based mixes.

7. Color-Seal

Color-Seal is a water based, low odor, acrylic stain and sealer designed to be applied over concrete, brick, block, stucco & concrete pavers. Color-Seal provides long lasting protection while improving the appearance of the substrate by adding color.

7. Paver-Lock Sand

A unique blend of high grade silica sand and polymer binders designed to be swept into paver joints to keep pavers securely in place.

7. Road Patch

A fast-setting, cement-based, highway patching compound and overlayment material used to restore concrete substrates requiring a minimum build-up of 2 inches. Ready for rubber wheeled traffic in 60 minutes.

7. Siloxane 20

Siloxane 20 is an exterior grade, solvent based, clear, deep penetrating water repellent designed to be applied over untreated concrete pavers, brick, block, concrete, stucco, and natural stone. Breathable, does not form a film or leave a sheen. May be used for vertical or horizontal applications.

7. U-Coat Primer 2180

.U-Coat Primer 2180 is a two-component, high solids, liquid applied, epoxy-polyamine primer with exhibits unique penetrating characteristics. U-Coat Primer is designed to be applied over properly prepared metal, concrete and plywood surfaces prior to the installation of U-Coat polyurethane coatings.

data sheet |   msds sheet  

7. U-Point

A single component, cement-based, polymer modified repointing compound used to point all types of masonry joints and may be used to grout between floor tile, marble and flagstone.

8. Elastoflex

A flexible, stretchable, waterborne acrylic, elastomeric coating which waterproofs and decorates exterior stucco, masonry and concrete walls. Elastoflex bridges hairline cracks and will stretch and move with the expansion of the building. Elastoflex is available in a variety of colors.

8. U-Coat Primer U

U-Coat Primer U is a two-component, high solids, liquid applied, re-coat primer designed to be applied over properly prepared, existing urethane systems prior to the installation of new U-Coat urethane coatings.

data sheet |   msds sheet  

9. Xtreme Weather-Block

Xtreme Weather-Block is a 100%, acrylic, elastomeric, waterproof membrane and air barrier designed for use as a water-resistive barrier behind exterior claddings including thin-stone veneer application. May be applied by roller, brush or suitable spray equipment.

Monostone

Monostone is a specially formulated combination of polymers, modifiers and aggregates designed to enhance aesthetics of architectural features while exhibiting high performance coating properties that may protect underlying surfaces. Monostone is water-based and ready to use. When cured, Monostone forms a plastic/aggregate matrix, resulting in tremendous compressive strength while exhibiting flexibility while its adhesion characteristics promote a lasting bond when proper surface preparation is combined with ASC Primer. Monostone may be applied over new or old masonry and concrete surfaces as well as wood and drywall

data sheet |   msds sheet  

Monostone Color Chart

Monostone Color Chart.

data sheet |   msds sheet  

Rainbow Cement Colors

Universal pigments used to tinit any type of cement or gypsum product including a variety of Umaco products.

data sheet |   msds sheet  

Standard Blended Flakes Color Chart

Click on "data sheet" (to the bottom right) for the Standard Blended Flake Color Chart.

data sheet |   msds sheet  

Standard Blended Quartz Color Chart

Click on "data sheet" (to the bottom right) for the Standard Blended Quartz Color Chart.

data sheet |   msds sheet  

Standard Epoxy Color Chart

Click on "data sheet" (to the bottom right) for the Standard Epoxy Color Chart.

data sheet |   msds sheet  

Standard Metallic Pigments Color Chart

Click on "data sheet" (to the bottom right) for the Standard Metallic Pigments Color Chart.

data sheet |   msds sheet  

Standard Polyaspartic Color Chart

.Click on "data Sheet" (to the bottom right) for the Standard Polyaspartic Color Chart.

data sheet |   msds sheet  

U-Coat 295

A two component, fast setting, rapid curing and solvent free, 100% solids hybrid aliphatic polyurea elastomeric membrane which can be applied in a single or multiple applications to properly prepared interior or exterior concrete, plywood and metal surfaces in temperatures as low as 20 degrees F.

U-Coat 3000

A low odor, water catalyzed, urethane polyurea, liquid applied, elastomeric waterproof membrane for horizontal surfaces. Typical uses include under tile, between slabs, green roofs, basements, bridges, I.R.M.A. roofs with insulation (pavers or ballasted), tunnels, planters. May be applied at any thickness, solvent free, quick curing and non-gassing.

U-Coat 5000 (Horizontal)

A single component, liquid applied, bitumen modified, coal tar free, polyurethane polyurea waterproofing membrane for vertical and horizontal surfaces ideal for foundations walls, between slabs, etc.

U-Coat 5000 (Vertical)

A single component, liquid applied, bitumen modified, coal tar free, polyurethane polyurea waterproofing membrane for vertical and horizontal surfaces ideal for foundations walls, between slabs, etc.

U-Coat 527

A two-part, UV stable, polyaspartic coating designed for a variety of applications that require minimal odor and maximum protection.

U-Coat Primer

A two component, high solids, liquid applied, epoxy-polyamine primer for Umacoat 260.

XBIS: Xtreme-Bond Installation System

XBIS: Xtreme-Bond Installation System Brochure

data sheet |   msds sheet